New Waste/Bulk Oil Transfer Pump for Heaters,Furnace,Generators,Air Compressors

Description

FOR MORE INFORMATION ABOUT OUR PUMPS, CALL 1-605-881-3473.
Bid with confidence. We have a money back return policy if your not satisfied.
Our feedback says it all!
This is a brand new (Made in USA)
Redline MP3500RSG
which features a
1/2 HP Industrial Grade
continuous duty 110 volt electric motor.
It has 3/4" NPT ports and will transfer most any type of oil up to 140 wt. Flow rate is up to 12 GPM. It will also pump cold oil!
This pump is built here in our shop in
Watertown, South Dakota
and we handle all service and warranty work.
It comes with a full 1 year warranty.
It can be used for bulk or waste motor oil, gear lube, transmission fluid, hydraulic oil, antifreeze, vegetable oil, diesel, and fuel oil.
Other features this redlinepump offers include our cast iron pumping unit with steel gears, a reduced speed electric motor which increases the pumps power, a heavy duty steel frame with carry handle, and a power cord with plug end. This pump has an adjustable built in bypass system which allows the user to use a trigger nozzle or a filtration system on the pressure side of the pump. This pump puts out up to 100 PSI. The pump can run while the output flow is cut off. Output rates vary with the type of oil and it's temperature. Diesel pumps at 12 GPM. WVO at room temperature will pump at 10 GPM. 15w40 diesel engine oil will pump at up to 10 GPM when it is above 50 degrees in temperature. These pumps are better than other pumps because they have the power to self prime with long suction hoses (20 feet) and are portable. It is better to have shorter suction hoses when possible because longer suction hoses will slow your flow rate. Another huge plus this pump offers is
NO DUTY CYCLE!
You can use it as long as you like without having to shut it off to cool. Other pumps you may see have duty cycles of 20 minutes or less. If you run them past their duty cycle their cheap little motors melt.  Many of them were never intended to pump any type of oil. Just water or diesel. Thin, easy to pump liquids- not thick oil. Again, redlinepumps are purpose built to move waste oil. They have a cast iron positive displacement gear pump instead of a cheap rubber flexible impeller or light duty composite or plastic blades that run inside of round chamber. As far as durability goes, a gear pump is best. All you need is a 1000 micron screen to keep out larger debris. 1000 micron is equal to screen door screen. Small vegetable matter (1000 Micron and smaller) has no effect on our gear pumps. Many other pumps you may find have to be screwed into a 2" bung on a barrel in order to suck out the oil. This is very inconvienient when you need to move the pump around to remote locations. With our system, you can put the pump where you want to and roll out a suction hose to your oil source and pump out the oil. A redlinepump is a purpose built system which makes oil transfer fast and easy. Also, with our pumps
1/2 HP
reduced speed
Industrial Grade
electric motor, you"ll have the power you need to transfer oil even when it's thick and cold. With the reduced speed motor, the motor and pump turn at 1100 rpm instead of 1800 rpm like most other pumps on the market. Other pumps on the market do not offer the reduced speed motor. This is why they fail when you try to pump a heavy or thick oil with them. Their pumping units and motors turn at 1800 rpm. No good for the tough jobs like oil filtration or cold weather oil transfer. This system uses 1" ID (1" ID hose should always be used if the oil is below 50 degrees in temperature.) 1" hose is .00 per foot. We offer a full line of accessories on our site.
Please call 1-605-881-3473 with any questions. Shipping is 0.00 to the lower 48 states. Canada shipping is 0.00.    Thanks,  redlinepumps  David L. Miller